ZigBee下載器SmartRF04EB仿真器支持CC2530/2541協議分析企業版

描述

ZigBee下載器SmartRF04EB仿真器支持CC2530/2541協議分析企業版

SmartRF04EB、CC系列無線芯片調試工具，可用於CC11xx、CC24xx、CC25xx等系列，支持多種常見的調試方法，如下載、仿真、調試、斷點、單步、全速、擦除、讀取、加密等，支持協議分析；
可以無縫連接到MCS-51編譯器的IAR730B，IAR751，IAR760，IAR810，支持以下工具：SmartRF Studio，SmartRF 閃存程序員，IEEE 地址程序員，包嗅探器。支援系統：WINXP/7/10 32&64bit;
完整版電路，不簡單集成版，雙BUFFER輸出，穩定可靠，兼容大多數國內模塊引腳。自動識別速度，下載速度高達150KB/S，向目標板提供3.3V。

The CC Debugger is primarily used for debugging and programming the flash on CCxxxx 8051-based System-on-Chip (SoC) devices from . CC Debugger also supports CCxxxx RF transceivers. In addition, CC Debugger is used for configuring the CC85xx devices with Pure Path Wireless Configurator.

Product Features

Performance Compatible with the original TI CC Debugger Supported Operating Systems: Windows 2000, Windows xp sp2/sp3, Windows Vista 32bit, Windows 7 32bit

Target voltage: 1.2V~3.6V

Capable of powering the target board from the debugger

Operating temperature: 0Â℃~85Â℃

Supported Software

IAR Embedded Workbench For C8051

SmartRF Flash Programmer

SmartRF Studio

SmartRF Packet Sniffer

PurePath Wireless Configurator

Connects to PC

Computer connection via USB interface

Connects to target board

Target board connection via 10-pin IDC connector (2×5 2.54mm pitch)

1. BCM2835 700MHz ARM1176JZFS processor with FPU and Videocore 4 GPU

2. GPU provides Open GL ES 2.0, hardware-accelerated Open VG, and 1080p30 H.264 high-profile decode

3. GPU is capable of 1Gpixel/s, 1.5Gtexel/s or 24 GFLOPs of general purpose compute and features a bunch of texture filtering and DMA infrastructure

4. 512MB RAM

5. Boots from Micro SD card, supports Linux distros such as Fedora, Debian and ArchLinux 

6. 10/100 wired Ethernet

7. HDMI output

8. USB 2.0 interface x 4

9. 4-pole 3.5mm stereo audio jack with composite video output

10. Micro SD card slot

11. Powered by 5v micro USB

12. Camera connector

13. 40-pin 2.54mm expansion pinheader

14. Dimensions: 85mm x 56mm x 17mm

LED Status

OFF: The debugger has no power or there is no valid firmware on the debugger.

AMBER (BOTH LEDS ON): The debugger is powered, but there is no valid firmware.

RED LED BLINKING: The Debugger is in Boot Recovery Mode.

RED LED ON: No device detected. This might be due to old firmware on the CC Debugger, or a problem with the hardware connection (make sure the target board is properly powered and connected correctly).

GREEN LED ON: The target device has been properly detected

• It is possible to start programming/debugging.

• More GPIO. The GPIO header has grown to 40 pins, while retaining the same pinout for the first 26 pins as the Model B.

• More USB. We now have 4 USB 2.0 ports, compared to 2 on the Model B, and better hotplug and over current behaviour.

• Micro SD. The old friction-fit SD card socket has been replaced with a much nicer push-push micro SD version.

• Lower power consumption. By replacing linear regulators with switching ones we’ve reduced power consumption by between 0.5W and 1W.

• Better audio. The audio circuit incorporates a dedicated low-noise power supply.

• Neater form factor. We’ve aligned the USB connectors with the board edge, moved composite video onto the 3.5mm jack, and added four squarely-placed mounting holes.